Width and length
| Width | Length | ||
|---|---|---|---|
| Nominal Width (mm) | Tolerance (mm) | Nominal lenght (mm) | Tolerance (mm) |
| De 1.000 a < 2.000 | De 4.000 a < 6.000 | +30-0 | |
| De 2.000 a < 3.000 | +20-0 | De 6.000 a < 8.000 | +40-0 |
| De 3.000 a ≤ 3.300 | +25-0 | De 8.000 a ≤ 10.300 | +50-0 |
| De 10.000 a ≤ 20.300 | +75-0 | ||
Thickness
| Thickness tolerance (mm) | Maximum thickness diference in a sheet (mm) | ||||||
|---|---|---|---|---|---|---|---|
|
Nominal thickness: d (mm) |
Types of tolerances |
– less |
+ More |
According to nominal width: b (mm): b (mm) | |||
| b < 2000 | 2000 ≤ b < 2500 | 2500 ≤ b < 3000 | 3000 ≤ b < 3500 | ||||
| 5 ≤ d < 8 | A | 0,40 | 1,10 | 0,90 | 0,90 | 1,00 | 1,00 |
| B | 0,30 | 1,20 | 0,90 | 0,90 | 1,00 | 1,00 | |
| C | 0,00 | 1,50 | 0,90 | 0,90 | 1,00 | 1,00 | |
| D | 0,75 | 0,75 | 0,90 | 0,90 | 1,00 | 1,00 | |
| 8 ≤ d < 15 | A | 0,50 | 1,20 | 0,90 | 1,00 | 1,00 | 1,10 |
| B | 0,30 | 1,40 | 0,90 | 1,00 | 1,00 | 1,10 | |
| C | 0,00 | 1,70 | 0,90 | 1,00 | 1,00 | 1,10 | |
| D | 0,85 | 0,85 | 0,90 | 1,00 | 1,00 | 1,10 | |
| 15 ≤ d < 25 | A | 0,60 | 1,30 | 1,00 | 1,10 | 1,20 | 1,20 |
| B | 0,30 | 1,60 | 1,00 | 1,10 | 1,20 | 1,20 | |
| C | 0,00 | 1,90 | 1,00 | 1,10 | 1,20 | 1,20 | |
| D | 0,95 | 0,95 | 1,00 | 1,10 | 1,20 | 1,20 | |
| 25 ≤ d < 40 | A | 0,80 | 1,40 | 1,10 | 1,20 | 1,20 | 1,30 |
| B | 0,30 | 1,90 | 1,10 | 1,20 | 1,20 | 1,30 | |
| C | 0,00 | 2,20 | 1,10 | 1,20 | 1,20 | 1,30 | |
| D | 1,10 | 1,10 | 1,10 | 1,20 | 1,20 | 1,30 | |
| 40 ≤ d < 80 | A | 1,00 | 1,80 | 1,20 | 1,30 | 1,40 | 1,40 |
| B | 0,30 | 2,50 | 1,20 | 1,30 | 1,40 | 1,40 | |
| C | 0,00 | 2,80 | 1,20 | 1,30 | 1,40 | 1,40 | |
| D | 1,40 | 1,40 | 1,20 | 1,30 | 1,40 | 1,40 | |
| 80 ≤ d < 150 | A | 1,00 | 2,20 | 1,30 | 1,40 | 1,50 | 1,50 |
| B | 0,30 | 2,90 | 1,30 | 1,40 | 1,50 | 1,50 | |
| C | 0,00 | 3,20 | 1,30 | 1,40 | 1,50 | 1,50 | |
| D | 1,60 | 1,60 | 1,30 | 1,40 | 1,50 | 1,50 | |
| 150 ≤ d | A | 1,20 | 2,40 | 1,40 | 1,50 | 1,60 | 1,60 |
| B | 0,30 | 3,30 | 1,40 | 1,50 | 1,60 | 1,60 | |
| C | 0,00 | 3,60 | 1,40 | 1,50 | 1,60 | 1,60 | |
| D | 1,80 | 1,80 | 1,40 | 1,50 | 1,60 | 1,60 | |
Flatness
| Nominal Thickness (mm) | Nominal thickness (mm) | Maximum sag (mm) | |||||
|---|---|---|---|---|---|---|---|
| Nominal width (mm) | |||||||
| < 1.500 | < 1.500 < 2.000 |
≥ 2.000 < 2.500 |
≥ 2.500 < 2.750 |
≥ 2.730 < 3.000 |
≥ 3.000 < 3.300 |
||
| ≤ 5 | 1.000 | 8 | 8 | 8 | 8 | 9 | – |
| < 8 | 2.000 | 13 | 13 | 13 | 14 | 15 | – |
| ≥ 8 | 1.000 | 7 | 7 | 7 | 7 | 8 | 8 |
| < 15 | 2.000 | 11 | 11 | 12 | 13 | 14 | 15 |
| ≥ 15 | 1.000 | 7 | 7 | 7 | 7 | 7 | 8 |
| < 25 | 2.000 | 10 | 10 | 10 | 12 | 12 | 14 |
| ≥ 25 | 1.000 | 6 | 6 | 6 | 6 | 6 | 7 |
| < 40 | 2.000 | 9 | 9 | 9 | 10 | 11 | 13 |
| ≥ 40 | 1.000 | 5 | 5 | 5 | 5 | 5 | 6 |
| < 70 | 2.000 | 8 | 8 | 8 | 9 | 10 | 11 |
| ≥ 70 | 1.000 | As agreed | |||||
| ≤ 140 | 2.000 | As agreed | |||||
The values of the table refers to steel types L with a minimum ReH > 460N/mm2 . For other steels, the tabulated values will increase in three units.